MAJIC+ COMMAND FILES FOR ARM ETM


The sample command files TRDEMODT.CMD and TRDEMO.CMD are user
modifiable files written to trace cdbdemo.c with and without data.
They load the cdbdemo.axf file into target memory, setup all ARM ETM
trace registers, set a breakpoint at __sys_exit, enable tracing, and
then run the cdbdemo on the target.


The following sample command files are working examples that you may
want to modify and/or use to see how the ETM aliased command files are used.


CLRETM:	This command file clears all ETM registers to a benign state.

EALLETM: Configures all ARM ETM Registers. This is an Example command file
	 that shows how to use all of the ARM ETM aliased command files.

ETRACE:	This is an Example command file that shows how to configure the ARM
	ETM Registers needed for Tracing. The TRDEMO and TRDEMODT command
	files use this file to setup Trace Regions and Trigger Event. The user
        may change the address ranges used for tracing and trigger event in
        this file.

EVIEW:	This is an Example command file that shows how to configure the ARM
        ETM Registers needed for ViewData. The TRDEMODT command file uses
        this file to setup Data Trace Regions. The user may change the address
        ranges used for Tracing Data in this file.




The following command files are located in the ./bin directory and are
aliased for use with the ARM ETM. These files SHOULD NOT be modified by
the user. The one exception to this rule is the ECTRL command file which
writes to the ARM ETM Control Register.

Examples files showing how to use these command files are described at the
beginning of this document.


ETMX:   This command file sets all ARM ETM command file aliases. It also sets
        all $ETMREG_... (ETM Register) globals used by ARM ETM command files.
        This file is not aliased.



EACMP:	This command file writes to the ARM ETM Address Comparator Register.
	Parameters passed:
	  Address Comparator Index
	  Address Value
	  Select Data Comparator
	  Select Masking of Address
	  Select Access Type

ECNTI:	This command file writes to the ARM ETM Initial Counter Register.
	Parameters passed:
	  Counter Register Index
	  Initial Count Value

ECNTR:	This command file writes to the ARM ETM Counter Event Registers.
	Parameters passed:
	  Counter Register Index
	  Event Register Location
	  [Counter Enable Control]
	  Resource Type  A
	  Resource Index A
	  Resource Type  B
	  Resource Index B
	  Boolean Function

ECTRL:	This command file Writes to the ARM ETM Control Register.
	All valid values for the Control register are configured and supplied
	in this command file. The user MUST EDIT this file to select the
	desired Control Register settings. Values are selected by commenting
	or un-commenting the appropriate lines.

	Parameters passed:
	  ETM Programming Bit

	NOTE: Firmware clears the ETM Programming Bit prior to Tracing

EDCMP:	This command file writes to the ARM ETM Data Comparator Register.
	Parameters passed:
	  Data Comparator Index
	  Data Value
	  Data Mask

EEVNT:	This command file writes to the ARM ETM Event Program Register.
	Parameters passed:
	  Event Register Pointer
	  Resource Type  A
	  Resource Index A
	  Resource Type  B
	  Resource Index B
	  Boolean Function

EFIFO:	This command file writes to the ARM ETM FIFOFULL Program Register.
	Parameters passed:
	  FIFOFULL Level
	  FIFOFULL inc/exc Control
	  Memory Map Decoders
	  Address Range Comparators

EMMAP:	This command file sets the ARM ETM Memory Map Decode Control Register.
	Parameters passed:
	  Memory Map Decode Control Value

ETRCE:	This command file writes to the ARM ETM TraceEnable Registers.
	Parameters passed:
	  Include/Exclude Control
	  Memory Map Decoders
	  Address Range Comparators

EVDAT:	This command file writes to the ARM ETM ViewData Control Registers.
	Parameters passed:	(ViewData Control 1)
	  ViewData Register 1
	  Addr Comparator Exclude Control         (bitwise [15:0])
	  Addr Comparator Include Control         (bitwise [15:0])

	Parameters passed:	(ViewData Control 2)
	  ViewData Register 2
	  Memory Map Exclude Control              (bitwise [15:0])
	  Memory Map Include Control              (bitwise [15:0])

	Parameters passed:	(ViewData Control 3)
	  ViewData Register 3
	  Addr Range Comparator Exclude Control   (bitwise [7:0])
	  Addr Range Comparator Include Control   (bitwise [7:0])
	  Control to Select Mixed Mode or Exclude Only      ([0])


DACMP:  This command file Reads and Displays the ARM ETM Address Comparator
	Registers.
	Parameters passed:
	  Address Comparator Index

DALL:   This command file Displays ALL the ARM ETM Registers

DCNFG:  This command file Reads and Displays the ARM ETM Configuration
	Register.

DCNTR:	This command file Reads and Displays the ARM ETM Counter Registers.
	Parameters passed:
	  Counter Register Index

DCTRL:  This command file Reads and Displays the ARM ETM Control Register.

DDCMP:  This command file Reads and Displays the ARM ETM Data Comparator
	Registers.
	Parameters passed:
	  Data Comparator Index

DEVNT:  This command file Displays a ARM ETM Event Register.
	Parameters passed:
	  Event Register

DFIFO:	This command file Reads and Displays the ARM ETM FIFOFULL Registers.

DIREG:  This command file Reads and Displays All ARM ETM Implementation
	Specific Registers.

DMMAP:	This command file Reads and Displays the ARM ETM Memory Map Decode
	Control Register.

DSEQ:   This command file Reads and Displays the ARM ETM Sequencer Registers.

DTRAC:	This command file Reads and Displays the ARM ETM TraceEnable Registers.

DTRIG:  This command file Reads and Displays the ARM ETM Trigger Event
	Register.

DVDAT:  This command file Reads and Displays the ARM ETM ViewData Registers.

DXALL:  This command file Reads and Displays All 128 ARM ETM Registers.
	NOTE:	Write Only Register values are cached by Majic firmware
		and show the last value written.

DXOUT:  This command file Reads and Displays the ARM ETM External Output
	Registers.

DXREG:  This command file Reads and Displays Any ARM ETM Register.
	Parameters passed:
	  ETM Register #